Description
The MERCUSYS MS106P is an unmanaged Fast Ethernet PoE+ switch designed to simplify the installation of IP surveillance and small-business networks by carrying both electrical power and network data over Ethernet cables.
The switch provides six 10/100 Mbps RJ45 ports. Ports 1–4 support PoE+, while ports 5–6 serve as non-PoE/uplink connections. MERCUSYS specifically highlights the two uplink ports for connections such as a router and an NVR when using Isolation Mode.
Four PoE+ Ports
Ports 1–4 support compatible IEEE 802.3af/at Powered Devices, allowing both power and network data to travel over a single Ethernet cable.
Compatible equipment can include:
- IP Cameras
- Wireless Access Points
- IP Phones
- Other IEEE 802.3af/at Powered Devices
Each PoE+ port supports up to 30 W, while the total PoE power budget is 67 W.
67 W Total PoE Budget
The MS106P provides up to 67 W of total PoE power shared across ports 1–4.
This allows several PoE-powered devices to operate without requiring separate power adapters near each camera, access point, or IP phone.
Two Dedicated Uplink Ports
Ports 5 and 6 provide data-only Fast Ethernet connections.
Typical uses include:
- Internet Router
- Network Video Recorder — NVR
- Additional Network Equipment
When Isolation Mode is active, MERCUSYS specifically identifies the two ports as uplinks, allowing one to connect to the internet/router and another to an NVR.
Extend Mode up to 250 Meters
For surveillance installations that require longer Ethernet runs, Extend Mode can increase PoE transmission distance to up to 250 meters.
This is particularly useful for cameras positioned far from the switch in warehouses, shops, parking areas, offices, or other large spaces.
When Extend Mode is activated, port speed is reduced to 10 Mbps. Actual achievable distance depends on cable quality, cable type, and connected-device power consumption.
Isolation Mode
Isolation Mode separates traffic on ports 1–4, helping reduce direct device-to-device communication and isolate broadcast traffic.
This is particularly useful in IP surveillance networks where cameras primarily need to communicate with an NVR or uplink rather than directly with each other.
Priority Ports 1–2
Ports 1 and 2 are designated priority ports. Prioritizing traffic from these ports helps maintain the quality of sensitive applications such as IP video and voice when network traffic becomes busy.
PoE Auto Recovery
The MS106P continuously monitors communication with PoE-powered devices.
If a connected PoE device becomes unresponsive for an extended period, PoE Auto Recovery can automatically reboot the device by cycling its power, helping reduce manual maintenance.
Durable Metal Housing
The metal enclosure helps provide efficient heat dissipation, network stability, and long-term durability.
The MS106P is also fanless, allowing quiet operation in homes, offices, shops, and surveillance cabinets.
Key Features
- 6-Port Fast Ethernet PoE+ Desktop Switch
- 6 × 10/100 Mbps RJ45 Ports
- 4 × 10/100 Mbps PoE+ Ports
- 2 × 10/100 Mbps Non-PoE / Uplink Ports
- IEEE 802.3af / 802.3at Compatible
- Up to 30 W per PoE Port
- 67 W Total PoE Budget
- Extend Mode up to 250 m
- Priority Ports 1–2
- Isolation Mode
- PoE Auto Recovery
- Auto-Negotiation
- Auto-MDI/MDIX
- IEEE 802.3x Flow Control
- Store-and-Forward Switching
- 1.2 Gbps Switching Capacity
- 2K MAC Address Table
- Auto MAC Learning
- Auto MAC Aging
- 2 KB Jumbo Frame
- Plug & Play
- No Configuration Required
- Durable Metal Housing
- Fanless Silent Operation
- Desktop Installation
- Wall Mounting
- Power / Link-Act / PoE Status LEDs
Technical Specifications
| Brand | MERCUSYS |
|---|---|
| Model | MS106P |
| Hardware Version | V1 |
| Product Type | Unmanaged Fast Ethernet PoE+ Switch |
| Total Ethernet Ports | 6 |
| Ethernet Speed | 10/100 Mbps |
| PoE+ Ports | Ports 1–4 |
| Non-PoE / Uplink Ports | Ports 5–6 |
| PoE Standard | IEEE 802.3af / IEEE 802.3at |
| Max PoE Power per Port | Up to 30 W |
| Total PoE Budget | 67 W |
| Auto-Negotiation | Supported |
| Auto-MDI/MDIX | Supported |
| PoE Power Pins | Power+: Pins 3 & 6 / Power-: Pins 1 & 2 |
| Extend Mode | Up to 250 m |
| Extend Mode Speed | 10 Mbps |
| Priority Ports | Ports 1–2 |
| Isolation Mode | Supported |
| PoE Auto Recovery | Supported |
| Switching Capacity | 1.2 Gbps |
| MAC Address Table | 2K |
| MAC Learning | Automatic |
| MAC Aging | Automatic |
| Jumbo Frame | 2 KB |
| Forwarding Mode | Store-and-Forward |
| Flow Control | IEEE 802.3x |
| Fanless | Yes |
| Enclosure | Metal / Steel |
| Installation | Desktop / Wall Mount |
| LED Indicators | Power / Link-Act / PoE Status |
| Dimensions | 99.8 × 98 × 25 mm |
| Network Cable — 10BASE-T | Cat3 or Above, up to 100 m |
| Network Cable — 100BASE-TX | Cat5 or Above, up to 100 m |
| Max Power Consumption — No PD | 2.07 W at 220V / 50Hz |
| Max Power Consumption — 67W PD Load | 76.85 W at 220V / 50Hz |
| Certification | CE / RoHS |
| Operating Temperature | -20°C to 40°C |
| Storage Temperature | -40°C to 70°C |
| Operating Humidity | 10%–90% RH, Non-Condensing |
| Storage Humidity | 5%–90% RH, Non-Condensing |
Main Benefits
Power and Data over One Ethernet Cable
PoE+ allows compatible cameras, access points, and IP phones to receive both electrical power and network connectivity over a single Ethernet cable, reducing installation complexity and the need for nearby electrical outlets.
Four High-Power PoE+ Connections
Each PoE port supports up to 30 W, giving the switch compatibility with a wide range of IEEE 802.3af/at devices.
67 W Shared Power Budget
A total 67 W PoE budget allows multiple PoE devices to operate simultaneously, subject to their individual power requirements.
Two Uplink Ports
Two dedicated non-PoE data ports provide convenient connections for a router and NVR, especially when deploying a small surveillance network.
Long-Range Surveillance Deployment
Extend Mode can increase PoE transmission distance to 250 meters, significantly extending deployment flexibility for cameras installed far from the network cabinet.
Automatic Recovery
PoE Auto Recovery can automatically restart certain unresponsive PoE devices without requiring someone to physically disconnect and reconnect them.
Better Camera Network Isolation
Isolation Mode separates PoE-port traffic, helping improve network stability and security for surveillance applications.
Durable and Silent Design
The metal enclosure improves heat dissipation and durability, while the fanless design keeps operation silent.
Recommended Uses
- CCTV Surveillance Systems
- IP Camera Networks
- Network Video Recorders — NVR
- Wireless Access Points
- IP Phones
- Small Offices
- Retail Stores
- Restaurants and Cafés
- Villas
- Small Businesses
- Dormitories
- Warehouses
- Home Surveillance
- Long-Distance Camera Installations
Package Contents
- 1 × MERCUSYS MS106P 6-Port 10/100 Mbps PoE+ Switch
- 1 × Power Adapter
- Rubber Feet
- 1 × Quick Installation Guide




Reviews
There are no reviews yet.